manual transmission RENAULT TWINGO RS 2009 2.G Electrical Equipment - Petrol Injection Workshop Manual

17B-209V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET089PROGRAMMING THE ENGINE FLYWHEEL TARGET–Not completed.
–Completed.
–Faulty (engine flywheel target fault).
STATUS
DEFINITIONCOMPLETED: This status indicates that the engine flywheel target programming has
been completed.
NOT COMPLETED: This status indicates that the engine flywheel target programming
has not been completed.
FAULTY: This status indicates that there has been an engine flywheel target fault.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
There must be no present or stored faults.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant temperature
> 80˚C
COMPLETED
or
NOT COMPLETED
or
"FAULTY"This status may be COMPLETED or NOT COMPLETED or FAULTY with the ignition
on or the engine running.
It varies according to the engine flywheel target status.
In the event of a fault, program the engine flywheel target (see Configurations and
programming).
If this status is FAULTY, refer to the interpretation of fault DF457 Engine flywheel
target.
Correct the present faults caused by the engine target and program the target by:
–Decelerate with the injection cut-off (no pressure on brake, accelerator and clutch pedals) between 3500 and
3000 rpm, for a minimum of 5 seconds in a gear above 2nd for an automatic transmission or above 3rd for
a manual gearbox.
–Decelerate a second time the injection cut-off (no pressure on brake, accelerator and clutch pedals) between
2400 and 2000 rpm, for a minimum of 5 seconds in a gear above 2nd for an automatic transmission or
above 3rd for a manual gearbox.
SIM32_V44_ET089/SIM32_V4C_ET089/SIM32_V50_ET089/SIM32_V54_ET089
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-231V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET415
CONTINUED 3
STATUS 3 Clutch pedal depressed
Manual gearbox only:
The cruise control function is deactivated when the gearbox is not coupled to the
engine (clutch pedal depressed).
Status ET415 becomes STATUS 3 when driving with cruise control active
(ET042 Cruise control/Speed limiter: CRUISE CONTROL) and the clutch pedal
is depressed.
This deactivates cruise control.
Reinitialise status ET415 of the injection computer by applying command
RZ001 Fault memory.
If status ET415 becomes STATUS 3 without the clutch pedal being depressed,
consult the interpretation of status ET405 Clutch pedal switch.
If the vehicle is fitted with automatic transmission:
Carry out a multiplex network test, check the configuration of the multiplex network
according to the vehicle's technical specifications and, in particular, the automatic
gearbox computer configuration (see 88B, multiplex).
STATUS 4 Cancel button pressed
The cruise control/speed limiter function is deactivated each time the suspend button
is pressed.
Status ET415 becomes STATUS 4, when driving when:
–Either the cruise control is active, or
–the speed limiter is active
–and when the "0" button is pressed by the driver.
This action deactivates the Cruise control/Speed limiter.
Reinitialise status ET415 on the injection computer by running command
RZ001.
If status ET415 becomes STATUS 4 without pressing the 0 button, consult the
interpretation of status ET703: Cruise control/speed limiter buttons and run fault
finding on the R/0 control button located on the right-hand side of the steering wheel.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-232V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET415
CONTINUED 4
STATUS 5 Cruise control or speed limiter monitoring
This status appears when the vehicle brakes or decelerates sharply without the
injection computer receiving a signal indicating that the brake pedal switch has
been pressed.
If status ET415 is STATUS 5, consult the interpretation:
–of status ET042 Cruise control/Speed limiter,
–of status ET703 Cruise control/Speed limiter buttons,
–of status ET704 Brake switch no. 1,
–and status ET705 Brake switch no. 2,
to test the cruise control/speed limiter system components and find the defective
component.
Also check the operation of the accelerator pedal, and check for any faults shown
on the diagnostic tool relating to this component. Deal with them if necessary.
Reinitialise status ET415 of the injection computer by applying command
RZ001 Fault memory.
If status ET415 becomes STATUS 5, deal with any faults that are present or stored
in the injection computer.
If the fault is still present, contact the Techline.
STATUS 6 Gear lever in neutral (manual gearbox) or neutral (automatic transmission).
Status ET415 changes to STATUS 6, when driving, with cruise control active
(ET042) and:
if the driver puts the gear lever in neutral position on a manual gearbox without
declutching or,
if the gear lever is in neutral on an automatic transmission.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command
RZ001.
If status ET415 becomes STATUS 6 without shifting the gear lever into neutral on
a manual gearbox without declutching, or into neutral on an automatic transmission,
test the ABS computer and check the configuration of the tyre size stored in the
computer. If the configuration is correct, contact the Techline.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.